Dispensing Robots

-) Can my material be applied in small quantities and repeatable?-) Can I dose it directly from the original container?-) Can my material be permanently exposed to compressed air or does it harden when exposed to air??-) How long can it be stored in cartridges or pressure tanks?-) Does it harden in the dispensing tips?-) Does it drip after dispensing? Does it pull strings? ... these are all questions that arise when using a new material. During a material test, we check the dispensing behaviour of your material with the appropriate dispensing technology. The costs depend on the customer requirements. The minimum cost is € 300,00. Your advantages after a material test: if the material can be dispensed with compressed air if the material can be dispensed directly from the original cartridge or must be transferred before if it has to be heated before dispensing how to prevent delay-yield or cob-webbing how long the material needs to cure on the workpiece how long it can be stored in the dispensing cartridge which "dispensing technology" is necessary for this (complete solution including all necessary fastening parts and brackets as well as tubing) which consumables will be used in the dispensing process you can calculate your costs in advance you know all settings regarding pressure, travel speed, tip diameter, cartridge size you can determine the cycle times and the productivity of the automated process   For a test setup we need: the material to be dispensed in the original cartridge (possibly in advance a technical data sheet) some workpiece samples description/sketch, where and how much material should be dispensed some general informations about the planned process: how many workpieces should be loaded per workday with the material? which cycle time should be reached? how much material will be needed per workpiece? is it already done by hand? Application in the industry: semiconductor PCB-components socketing and bonding LCD-bonding electrical components (such as relays, speakers, batteries) automotive clothing medicine optics used materials: fats silicones 2k-bondings solder pastes conductive adhesives uv-adhesives epoxy resins sealants other liquid materials  

In a dispensing setup with a robot, we set up your application in our laboratory and dispense your material on your workpiece samples. As part of the test setup, we optimize the process by using the most appropriate valves and also testing the correct settings for pressure, travel speed and tip diameter for your material. We will document the results for you via video and pictures. We will send the workpieces back to you so that you can finalize them. On request, you can also view the dispensing process personally and "live" during a visit to us. The minimum cost of a roboter testsetup is € 600,00. Our offer for you: When placing the order for the robot dispensing solution shown, 50% of the test setup costs will be credited* to the order amount!*) onetime valid for one tested material and one workpiece sample type   Your advantages after a test setup: You can be sure that your planned automated application is actually working Which "dispensing technology" is necessary for this (complete solution including all necessary fastening parts and brackets as well as tubing) Which consumables will be used in the process You can calculate your costs in advance You know all settings regarding pressure, travel speed, tip diameter, cartridge size You can determine the cycle times and the productivity of the automated process Upon request, we will create the final robot program for you (optional, upon agreement and expense, final workpiece holder compulsory)  For a test setup we need: The material to be dispensed in the original cartridge (possibly in advance a technical data sheet) Some workpiece samples Description/sketch, where and how much material should be dispensed Some general informations about the planned process: How many workpieces should be loaded per workday with the material? Which cycle time should be reached? How much material will be needed per workpiece? Is it already done by hand?   Application in the industry: semiconductor PCB-components socketing and bonding LCD-bonding electrical components (such as relays, speakers, batteries) automotive clothing medicine optics used materials: fats silicones 2k-bondings solder pastes conductive adhesives uv-adhesives epoxy resins sealants other liquid materials

This benchtop dispensing robot is suitable for all dispensing devices, valves and dispensing components of all manufacturers. The self-supporting case is completely made of aluminum and steel, the axes are driven by robust stepper motor with ball-bearing toothed belts. The workpiece is clamped on the 300 x 300 mm worktop. The worktop moves along with the workpiece in the X-direction, the material to be dispensed is applied to the workpiece from above via the metering unit movable in the Y- and Z-directions (for example metering valve, dispensing cartridge, etc.). The entire control unit is located in the robot base, which means that the device can be installed in a very space-saving manner. The control unit is programmed via the included Windows PC software. The control unit is able to manage up to 100.000 processing points in 255 different programs. There are 2 digital inputs and 4 digital outputs available for communication between the robot and various external systems. The device can optionally be equipped with 16 I/O ports and an analogue output (for controlling a volumetric pump). Properties: simple operation and commissioning, no programming knowledge required compact, robust and space-saving design user interface in english repeatability +/- 0,1 mm per axis max. speed: 1 - 250 mm/sec. (X-, Y-axis)1 - 100 mm/sec. (Z-axis) workspace: 300 x 300 x 140 mm Application in the industry: semiconductor PCB-components socketing and bonding LCD-bonding electrical components (such as relays, speakers, batteries) automotive clothing medicine optics used materials: fats silicones 2k-bondings solder pastes conductive adhesives uv-adhesives epoxy resins sealants other liquid materials   specification GP-WRL300 axis drive 3-axis table robot with ball-bearing toothed belts axes programming remote mode (self-learning) via PC software, import of profiles from DXF and Gerber Files control module ALPHA CP RS232 CanOpen® I/O interpolation point-to-point and continuous path (CP)

* The shipping costs for this product are calculated manually * * The price listed is for a 3-axis table-top robot  * This benchtop dispensing robot is suitable for all dispensing devices, valves and dispensing components of all manufacturers. The self-supporting case is completely made of aluminum, the axes are driven by robust, ball-bearing spindle axes. The workpiece is clamped on the 300 x 300 mm worktop. The worktop moves along with the workpiece in the X-direction, the material to be dispensed is applied to the workpiece from above via the metering unit movable in the Y- and Z-directions (for example metering valve, dispensing cartridge, etc.). The entire control unit is located in the robot base, which means that the device can be installed in a very space-saving manner. The control unit is programmed via the included PC software, in which already existing profiles, .dxf files and gerber files can be imported. The control unit can manage up to 100.000 processing points in 255 different programs. In addition, 16 I/O-ports are available for communication between the robot and various external systems. The device can optionally be equipped with a protective housing (mechanical and / or photocells). It is also possible to equip the robot with a fourth axis (rotation axis) or to expand an optical tip alignment system. Further informations can be found in our brochure. Properties: simple operation and commissioning, no programming knowledge required compact, robust and space-saving design user interface in english repeatability +/- 0,015 mm per axis max. speed: 1 - 600 mm/sec. (X-, Y- and Z-axis) workspace: 300 x 300 x 145 mm Application in the industry: semiconductor PCB-components socketing and bonding LCD-bonding electrical components (such as relays, speakers, batteries) automotive clothing medicine optics used materials: fats silicones 2k-bondings solder pastes conductive adhesives uv-adhesives epoxy resins sealants other liquid materials   specification GP-WRA300 axis drive 3- / 4-axis table robot with ball-bearing spindle axes programming remote mode (self-learning) via PC software, import of profiles from DXF and Gerber Files control module ALPHA CP RS232 CanOpen® I/O interpolation linear and 3D circular on X,Y,Z point-to-point and continuous path (CP)

* The shipping costs for this product are calculated manually * * The price listed is for a 3-axis table-top robot  * This benchtop dispensing robot is suitable for all dispensing devices, valves and dispensing components of all manufacturers. The self-supporting case is completely made of aluminum, the axes are driven by robust, ball-bearing spindle axes. The workpiece is clamped on the 500 x 500 mm worktop. The worktop moves along with the workpiece in the X-direction, the material to be dispensed is applied to the workpiece from above via the metering unit movable in the Y- and Z-directions (for example metering valve, dispensing cartridge, etc.). The entire control unit is located in the robot base, which means that the device can be installed in a very space-saving manner. The control unit is programmed via the included PC software (Windows), in which already existing profiles, .dxf files and gerber files can be imported. The control unit can manage up to 100.000 processing points in 255 different programs. In addition, 16 I/O-ports are available for communication between the robot and various external systems. The device can optionally be equipped with a protective housing (mechanical and / or photocells). It is also possible to equip the robot with a fourth axis (rotation axis) or to expand an optical tip alignment system. Further informations can be found in our brochure. Properties: simple operation and commissioning, no programming knowledge required compact, robust and space-saving design user interface in english repeatability +/- 0,015 mm per axis max. speed: 1 - 600 mm/sec. (X-, Y- and Z-axis) workspace: 500 x 500 x 145 mm Application in the industry: semiconductor PCB-components socketing and bonding LCD-bonding electrical components (such as relays, speakers, batteries) automotive clothing medicine optics used materials: fats silicones 2k-bondings solder pastes conductive adhesives uv-adhesives epoxy resins sealants other liquid materials   specification GP-WRA500 axis drive 3- / 4-axis table robot with ball-bearing spindle axes programming remote mode (self-learning) via PC software, import of profiles from DXF and Gerber Files control module ALPHA CP RS232 CanOpen® I/O interpolation linear and 3D circular on X,Y,Z point-to-point and continuous path (CP)

This gantry dispensing robot is particularly suitable for very heavy workpieces or if low-viscosity (very low-viscosity) dispensing materials are used, which would easily spill over when the workpiece - as in a table robot - would be moved back and forth in the x direction. All dispenser, valves and dispensing components of all manufacturers can be used. In contrast to a table robot, the workpiece doesn't move with the x-axis. Above the workpiece, the robot moves with the material to be dispensed in the X, Y and Z directions. In this case, a working space of 500 x 500 x 145 mm can be covered in the standard version shown above. The robot is equipped with a protective case. Apart from this standard version, this portal robot can also be assembled in various customer-specific versions: -) the working space can be freely selected in a range between 400 x 400 mm to 2000 x 3000 mm -) the tool load on the vertical axis can be increased up to 15 kg -) the axes movement speeds can be increased up to 1.000 mm/s -) the robot can be equipped with a fourth axis (rotation axis)   The entire control unit is occasionally under the protective case. A control panel on the controller retrieves, starts and stops dispensing programs. The control unit is programmed via the provided PC software with a user-friendly graphical interface, whereby existing profiles, .dxf files and gerber files can be imported. The control unit can manage up to 255 different programs and up to 100,000 edit points. Furthermore, up to 16 I / O ports are available for communication between the robot and various external systems.   Do not hesitate to request us for your individual automation solution!   Properties: simple operation and commissioning, no programming knowledge required< user interface in german, english, spanish, italian and polish compact und robust construction CE approved protective case repeatability +/- 0,1 mm per axis movement speed (standard-version): 400 mm/sec. (X-, Y- and Z-axis) workspace (standard-version): 500 x 500 x 145 mm  Application in the industry: semiconductor PCB-components socketing and bonding LCD-bonding electrical components (such as relays, speakers, batteries) automotive clothing medicine optics  used materials: fats silicones 2k-bondings solder pastes conductive adhesives uv-adhesives epoxy resins sealants other liquid materials   specifikation GP-TL5050 storage 9999 programs on CF-card, PC STORAGE & USB axis drive 3-/ 4-axis portal robot with bipolar stepper motor programming remote mode (self-learning) via PC software, import of profiles from DXF and Gerber Files control module ALPHA CP RS232 CanOpen® I/O interpolation linear and 3D circular on X,Y,Z point-to-point and continuous path (CP)

No matter if you have to produce small to medium-sized series or want to fill various materials in bottles or cartridges - we can do that for you!  Examples of possible applications: -) Applying adhesive seals-) Embedding of electronic parts or circiut boards-) Filling joints-) Conglutination of emblems-) Transfer of materials from large containers into all marketable cartridges.-) Filling perfume testing-bottles-) Filling of soldering paste in cartridges.etc. We are also available at short notice for such and similar applications.Ask us, we will contact you to clarify further details!