Our pinch tube valve is suitable to dispense semi-viscous materials including two-part fluids, cyanoacrylates as well as other liquids such anaerobics, which dictate “non-metallic” valves. Only the PE pinch tube gets in contact with the material. Should the material cure inside the hose, the pinch tube assembly can be easily replaced. The pinch tube valve is closed with an internal spring. Compressed air is used to open the piston against the spring force. This allows the material to flow. The shot size or flow rate is determined by the viscosity and the pre-pressure of the material as well as the valve control timer. You can connect dispensing tips or material supply hoses easily to the LuerLock connections of the pinch tube. Our dispensers can be used as compressed air controls. Info: equivalent to 710-HPNM   Delivery contents: -) valve-) pinch tube-) dispensing tips - set-) manual-) control air hose   Accessories: -) valve holder IG-FU-1212-016-MSRC-) pinch tube (in desired lenghts)   Technical details:  material inlet:  LuerLock female  material outlet:  LuerLock male  material pinch tube:  PE  weight:  83 g  dimensions:  75mm lenght  operating pressure:  4 - 7 bar    

Our high pressure spool valve is suitable to dispense high flow rates of medium to high viscosity materials. The reverse action closure of the valve provides a “suck-back” effect. The valve opens with the control air (min. 4bar). Usually the valve closes with spring force when the controll air is off. Optionally auxiliary air can be used for faster closure. Our dispensers can be used as compressed air controls. In order to be able to remove coarse remnants of the dispensing material from the valve, we recommend our conditioner. The valve body is made from high quality Stainless Steel! Previous article number: 790HPNM   Technical details:  material inlet:  1/4" NPT thread  material outlet:  1/4" NPT thread  control air inlet:  1/4" NPT thread  weight:  520 g  dimensions:  118mm lenght, Ø 38 mm  operating pressure:  4 bar  operation frequency:  600 Zyklen/min.  flow rate (water at 100psi):  39.000 ml/min.  fluid viscosity range:  up to 3.000.000 mPas  fluid pressure:  max. 170 bar    

Our diaphragm dispensing valve is suitable to dispense low to medium viscosity materials. The wetted parts are separated from the valve control units. This is excellently well suited for dispensing aggressive or very low viscosity materials like paints, inks, cyanoacrylates or oils, especially when high frequency output cycles of small dosing quantities are required. The respective quantities can be exactly set via a fine adjustment on the head of the valve. Our dispensers can be used as compressed air controls. In order to be able to remove coarse remnants of the dispensing material from the valve, we recommend our conditioner. The valve body is made from high quality Stainless Steel!   Technical details:  material inlet:  1/8" NPT thread  material outlet:  LuerLock male  control air inlet:  M5 thread  weight:  87 g  dimensions:  80mm lenght, Ø 27 mm  operating pressure:  4 bar  operating frequency:  500 cycles/min.  flow rate (water at 100psi):  300 mL/min.  fluid viscosity range:  up to 50.000 mPas  fluid pressure:  max. 5 bar

Our Spool valve is suitable to dispense medium to high viscosity materials. The reverse action closure of the valve provides a “suck-back” effect, which is easily adjustable via a set screw on the valve. This is very helpful and prevents undesirable after-dropping of the material. The valve opens with the control air (min. 3,5bar). Usually the valve closes with spring force when the control air is off. Optionally auxiliary air can be used for faster closure. Our dispensers can be used as compressed air controls. In order to be able to remove coarse remnants of the dispensing material from the valve, we recommend our conditioner. The valve body is made from high quality Stainless Steel!   Technical details:  material inlet:  1/8" NPT thread  material outlet:  1/8" NPT thread  contlrol air inlet:  M5 thread  weight:  160 g  dimensions:  lenght 102mm, Ø 35 mm  operating pressure:  min. 3,5 bar  operating frequency:  700 cycles/min.  flow rate (water at 100psi):  2.700 mL/min.  fluid viscosity range:  up to 1.000.000 mPas  fluid pressure:  max. 34bar

The needle valve is suitable for dispensing of low to medium viscosity materials. It enables to apply even extremely small individual shots of material. The valve opens with the control air (min. 5bar). Usually the valve closes with spring force when the controll air is off. Optionally auxiliary air can be used for faster closure. Of course the flow rate of the material depends on the viscosity rate of the material and the pre-pressure of the material but it can be easily adjusted over the rotating wheel on the valve. Our dispensers can be used as compressed air controls. In order to be able to remove coarse remnants of the dispensing material from the valve, we recommend our conditioner. The valve body is made from high quality Stainless Steel!   Technical details:  material inlet:  1/8" NPT thread  material outlet:  LuerLock male  compressed air inlet:  M5 thread  weight:  210 g  dimensions:  lenght 115mm, Ø 28,5mm  operating air pressure:  min. 5 bar  operating frequency:  600 cycles/min.  flow rate (water at 100psi):  1.680 ml/min.  fluid viscosity rate:  up to 100.000 mPas  fluid pressure:  max. 20 bar